date:2014/10/20 http://www.nhel.com.cn page: 1 of 3 rev.:aa production data sheet niu hang electronic co. ltd k09 0 thru k260 70 to 220 volts high voltage bidirectional trigger diode the plastic package carries underwriters laboratory flammability classification 94v-0 bidirectional crowbar protection fast response high forward surge current capability high temperature soldering guaranteed 250 c/10 seconds on terminals fea tures smb/do214aa dimensions in millimeters high surge current capability the rmal considerations sy mbol parameter value unit t j o perating junction temperature range -40 to +125 c t s s torage temperature range -65 to +150 c r ja th ermal resistance: junction to ambient 90 c/w average on-state current (av) 1.0 a maximum surge current (50h ) 4.0 a t tsm i t case : jedec do-214aa molded plastic body t erminals : plated leads, solderable per mil-std-750, method 2026 mounting position : any weight : 0.0048 ounce, 0.136grams mechanical da ta el ectrical parameters pa rt number v drm vo lts v volts i dr m a mps i h ma mps i mamps v tm k090 70 1 80 100 0.5 10 50 2.0 k110 95 1 100 120 0.5 10 50 2.0 k120 100 1 110 130 0.5 10 50 2.0 k130 110 1 120 140 0.5 10 50 2.0 k140 120 1 130 150 0.5 10 50 2.0 k160 140 1 150 170 0.5 10 50 2.0 k180 160 1 170 190 0.5 10 50 2.0 K200 180 1 190 210 0.5 10 50 2.0 k220 190 1 210 230 0.5 10 50 2.0 k240 200 1 230 250 0.5 10 50 2.0 k260 220 1 250 270 0.5 10 50 2.0 min max bo min max bo vo lts max min max max k105 90 1 95 115 0.5 10 50 2.0 k150 130 1 140 160 0.5 10 50 2.0
production data sheet niu hang electronic co. ltd page: 2 of 3 date:2014/10/20 rev.:aa k09 0 thru k260 70 to 220 volts high voltage bidirectional trigger diode ratings and characteristic curves k0 90 thru k260 v -i characteristics -v +i v drm +v v s i s i h r s i drm i bo v bo v t i t (i s - i bo ) (v bo - v s ) r s = -i pea k surge current versus surge current duration normalized dc holding current versus case/lead temperature 1.0 10 100 1000 1.0 2.0 4.0 6.0 8.0 10 20 40 supply frequency: 60 hz sinusoidal load: resistive rms on-state current: i t rms maximum rated value at specified junction temperature notes: 1) blocking capability may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. surge current duration ? full cycles peak surge (non-repetitive) on-state current [i tsm ] ? amps 100 0 0.5 1.0 2.0 1.5 -15 -40 +25 +65 +105 +125 case temperature (t c ) ? ? c i h i h (t c = 25 ? c) ratio of 50 100 0 t r t d 0 peak va lue half v alue t ? time (s) i pp ? peak pulse current ? %i pp t r = rise time to peak value t d = decay time to half value w aveform = t r x t d t r x t d p ulse wave-form r epetitive peak on-state current (i trm ) v ersus pulse width at various frequencies normalized repetitive peak breakover current versus junction temperature di/dt limit line 0.6 0.8 4 2 4 6 8 10 20 40 60 80 100 200 400 600 2 x 10-3 68 1 x 10-2 24 68 1 x 10-1 24 681 1 pulse base width (t o ) ? ms repetitive peak on-state current (i trm ) ? amps v bo firing current waveform non-repeated repetition frequency f=5 hz f = 10 hz f = 100 hz f = 1 khz f = 5 khz f = 10 khz f = 20 khz t j = 125 oc max to i trm l/f non-repeated 20 30 40 50 60 70 80 90 100 110 120 130 1 2 3 4 5 6 7 8 9 junction temperature (t j ) ? ? c repetitive peak breakover current (i bo ) multiplier v = v bo http://www.nhel.com.cn
page: 3 of 3 date:2014/10/20 rev.:aa production data sheet niu hang electronic co. ltd k09 0 thru k260 70 to 220 volts high voltage bidirectional trigger diode maximum allowable ambient temperature versus on-state current normalized v bo ch ange versus junction temperature on-state current versus on-state voltage (typical) power dissipation (typical) versus on-state current [refer to figure e9.14 for basic sidac circuit] 0 0.2 0.4 0.6 0.8 1.0 20 40 60 80 100 120 140 25 rms on-state current [i t(rms) ] ? amps maximum allowable ambient temperature (t a ) ? ?c current waveform: sinusoidal - 60 hz load: resistive or inductive free air rating -12 -20 0 +20 +40 +60 +80 +100 +120 -10 -8 -6 -4 -2 0 +2 +4 -40 +25 junction temperature (t j ) ? ?c percentage of v bo change ? % +140 0 0.8 1.21.0 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3. 6 0 1 2 3 4 5 6 7 8 9 positive or negative instantaneous on-state voltage (v t ) ? volts positive or negative instantaneous on-state current (i t ) ? amps t l = 25 ?c 0.2 0.4 0.6 0.8 1.0 0 0.4 0.8 1.2 1.6 0.2 0.6 1.0 1.4 1.8 2.0 2.2 rms on-state current [i t(rms) ] ? amps average on-state power dissipation [p d(av) ] ? watts current waveform: sinusoidal load: resistive or inductive conduction angle: see basic sidac cirucit ratings and characteristic curves k0 90 thru k260 http://www.nhel.com.cn
|
